|Bill Wheeler||24/12/2018 12:21:36|
|24 forum posts|
Hello All. I need to remove rust from several tools (yes, my workshop lets in draught, but that's another task). I've looked at a solution called Evapo-Rust - 5L, £40.00. Does any one have any alternative methods of removing / eliminating rust from metal hand tools? Many thanks.
|Derek Lane||24/12/2018 14:19:33|
3219 forum posts
How much rust is on them. For light rust a very light sand with Wet and dry sand paper using a light oil then wipe off if it heavily rusted then look at either chemical rust removers.
|Ron Davis||24/12/2018 16:07:35|
1619 forum posts
I agree with Derek, wet or dry, elbow grease and patience!
There are other ways, washing soda in water and a car battery charger appears to work, though I have yet to try it.
Fortyquid seems a lot, though it depends on how much you value your tools
|derek willis 1||26/12/2018 10:11:32|
99 forum posts
There was a video on here some years ago, about using a 12volt battery
and 2 electrodes connected placed either end of a tank of solution, place
tools in, and turn on. Must be on the internet, so search.
|29 forum posts|
|Use a Nylon scourer (Scotchbrite) pad. Lubricate with beeswax. I find the 'spray' stuff from Wilko's is excellent for doing this. I use it on the cast iron tables on my saw etc and on hand tools. A fine misting is all you need. |
Only use more aggressive methods if the tools are not flat and true.
|Bill Wheeler||27/12/2018 09:56:25|
|24 forum posts|
Hello All. Many thanks for your suggestions. I understand the Evapo-Rust can be reused, but I agree with Ron that 40 pounds is expensive. I have a perennial problem with my tools so I'll try the nylon pad and beeswax to see if that offers a more long-term solution. In the meantime, I need to draught-proof my garage turned workshop.
|John Baddeley||31/12/2018 18:13:22|
|54 forum posts|
As an aside, I can't help thinking it's not the draught, but damp and cold leading to condensation. (Sorry, I'm very pedantic!)
Movement of air is a good thing, surely, just make sure your workspace doesn't get warm or damp, and then cold.
If the space is really difficult to keep sufficiently dry, maybe it's worth having a cupboard for your hand tools [not practical for big machines] and put a light bulb in the bottom and leave it on to maintain a little warmth. (If you like this idea, please check thoroughly that nothing gets too warm! I won't be held responsible for a fire!!)
And if I'm talking through my hat, tell me!
|Bill Wheeler||01/01/2019 09:59:56|
|24 forum posts|
Hello John, Thanks for your words of wisdom. My workspace does not get warm, I've spent some time updating/converting my garage into a usable workshop - replacing all windows for uPVC non-openers and new doors, but yet to solve the issue of air coming in through gaps in the roofing (corrugated profile) sheets. I'll use your suggestion of making cupboards for my planes etc after I've cleaned off the rust. Looking at a video of the Evapo-Rust, it really works well to completely clean off heavy rust. I've seen 5L for 30 pounds so might try this if all else is unsatisfactory. Happy New Year all.
|Cedric Wheeler||04/01/2019 20:39:03|
|154 forum posts|
I spray all my tools ( including lathe beds and chucks etc) at the onset of the cold weather with WD40 then just wipe off the excess. This will normally keep them clean until it warms up again.
|Alan Robinson 3||29/01/2019 08:36:18|
|4 forum posts|
Hello although a new member, may I suggest soaking them in red wine vinegar, have done this very successfully with some badly rusted tools and on cast iron as well. Soak for as long as possible, a few days at least, then a light wire brush, I used a brass one, then a bit of spray to protect.
|Elizabeth Brown 3||29/04/2019 17:14:01|
|1 forum posts|
Which spray did you use to protect the tools?
|Alan Robinson 3||02/05/2019 11:41:05|
|4 forum posts||
Just a bit of WD40, sprayed on then a gentle wipe off with kitchen roll, obviously when useing them you get your hands dirty but I didnt find them slippy. On the cast iron which was a French bread oven door, I coated it with a black paste and buffed it up, sorry dont know what you would call it in the Uk.
|John Baddeley||02/05/2019 12:55:09|
|54 forum posts|
my first thought re. black paste would be 'grate black' [or blacking]
googling 'grate blacking' produces several hits.
|Josephe Tanenbaum||08/08/2019 12:02:24|
|6 forum posts||
|Tom Albrecht||15/08/2019 05:15:24|
1 forum posts
If you can submerse the tool in white vinegar for a couple of days it works a treat. I used this method for some engineer's hammer heads before I re-handled them. When you take them out of the vinegar and they are still wet, rub them with some scrunched up aluminium cooking foil.
Rinse them in water and a little baking soda to neutralise the vinegar. Then dry.
I am going to give this a go on some handsaws I want to clean up.
Please login to post a reply.
Want the latest issue of The Woodworker & Good Woodworking? Use our magazine locator links to find your nearest stockist!
We're always happy to hear from you, so feel free to get in touch!