By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for Mark Sutton

Here is a list of all the postings Mark Sutton has made in our forums. Click on a thread name to jump to the thread.

Thread: Birch Burr
15/10/2009 10:47:21
Thank you Gents.
 
Alan, no injuries sustained, just had to be careful!!
Thread: Using yew
13/10/2009 08:05:28
Hi Geoff
 
I personnally wouldn`t, i would use Beech or Sycamore, but others may have other ideas
 
Mark
Thread: Birch Burr
13/10/2009 08:03:48
Hi Dennis
 
Many thanks, i picked up 5 of these burrs, 4 to do!!
 
Mark
Thread: banksia nut
13/10/2009 08:02:45
Ralph
 
What a beautiful pot, i just love the concept.  Well Done
Thread: Mark's Miniature Birdhouse
12/10/2009 07:59:25
Thank you Ralph & Marc.
 
Must remember to keep the Flies!!!
Thread: Birch Burr
12/10/2009 07:58:09
Thank you Ralph.
 
I enjoyed turning the Burr, not very often you get Birch though.
 
Turning off centre was not to bad, i lost a very small piece of it though!!
Thread: sharpening woodturning chisels
11/10/2009 19:01:03
Hi Richard
 
As many have said, we use different angles.  I used to have a little chart for the angles, i must see if i can find it again!!
 
My bowl gouges are all at 45 degrees, with an extra wee grind just below that at about 35 degrees.
Spindle roughing gouge at 45 degrees
All my spindle gouges are a long fingernail profile.
Thread: Birch Burr
11/10/2009 18:51:06
Hi All
 
Just thought i would show you all my latest Burr Attempt!!  Finished in Danish Oil
 
Thread: Mark's Miniature Birdhouse
11/10/2009 18:42:34
Hi Marc
 
Many thanks
 
The base is made from Cherry, with a purpleheart insert
The birdhouse is:-    Roof - African Blackwood
                                House is Spalted sycamore
                                Perch and Finial is Padauk

House measures 2" from top to bottom!!
 
Mark
Thread: Vaughn's segmented vase
04/10/2009 19:43:32
Nice piece Vaughn.
 
What woods were used?
 

Thread: Small Lathe Recommendations...
04/10/2009 19:42:03
Hi
 
I have a Record CL4, so i don`t need to change any fittings when i take my chuck into the club, to do demonstrations, you are right there is no difference between the 305 and the 305VS bar the variable speed, and of course there is the 5yr waranty
 
My first lathe was a Clarke bench top, it didn`t last that long, it was`nt big enough, then i had the yellow perform, but again that didn`t last long, i needed a bigger lathe.  If i had the money i would buy the 305 VS, as i find the variable speed a boon, i can`t be bothered to change belt speeds all the time. 
03/10/2009 19:51:17
Hi Ben
We have two of the DML305 VS`s (variable) in my local club, not the DML305, lovely little machines to use, easily moveable, ideal for the demonstrations etc.  They even have ability for indexing.
 
Mark
Thread: oak burr bowl
02/10/2009 19:50:52
Hi Dennis
 
The edge are always the worst, you just hope you don`t lose any of the natural edge when turning it.
 
I have just taken delivery of some Birch Burrs, which are difficult to get a hold of and I have turned two of them of them, will post photos pretty soon
Thread: Fruit Bowl
02/10/2009 19:47:33
I agree with the comments, nice wood.
 
I was doing some recycling just lately and took delivery of a few nice pieces of Douglas Fir, must turn something out of them.
Thread: Derek's pen
02/10/2009 19:41:57
Padauk, finishes very well, its a bit of a messy wood though, red dust everywhere!!!
02/10/2009 19:30:10
Good Luck with selling your pens, what kind of wood is it?
 
I havn`t turned any for a while!!
Thread: Ralph's new turned project
02/10/2009 19:26:05
  A Little bit late, i like the piece, nice use of different timbers Well done
Thread: Just an Experiment
02/10/2009 19:23:05
I like the knotwork, i have tried it a couple of times and failed, mind you i was turning a Goblet head at the time, and it gave way, must try it again.
Thread: Listen up all you Woodturners...
02/10/2009 19:18:42
Hi
 
Its been a while since last on, day job keeping me busy.
I wouldn`t mind entering, but it is a long way for me living the Highlands, not that i am being negative in anyway, i Love competitions
Thread: oak burr bowl
19/09/2009 20:05:32
Hi Dennis
 
Lovely work, and a nice piece of Pippy Oak, with lots of character, well done.  I love turning burrs myself.
 
Mark
Magazine Locator

Want the latest issue of The Woodworker incorporating Good Woodworking? Use our magazine locator links to find your nearest stockist!

Find The Woodworker inc Good Woodworking 

Latest Forum Posts
Support Our Partners
Triton
Wood Workers Workshop
Peter Sefton IMPROVE FAST LONG
Transwave 2017
Felder UK April 2016
D B Keighley
Turners Tool Box
Tormek
D&M Tools
Tool Post
Chippendale
Subscription Offers

Subscribe to<br />    The Woodworker Magazine and receive a FREE gift

Contact Us

We're always happy to hear from you, so feel free to get in touch!

Click here to find who to contact