By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for Doug

Here is a list of all the postings Doug has made in our forums. Click on a thread name to jump to the thread.

Thread: spalted beech hollow form.
28/03/2017 20:59:14

Looks very good Dennis yes

Thread: Veneer Rippling
14/03/2017 07:41:43

 

Hi Steve,

I don't do a lot of veneering mainly inlays but I was fortunate to see David Savage a couple of years back at the European Woodworking show when he was demonstrating veneering techniques.

On badly shaped or wrinkled veneers he recommended using an ordinary household iron to flatten it prior to use, it may be worth trying out on a wetted off cut of veneer ironing through a dampened cloth.

Best of luck,

 

Edited By Doug on 14/03/2017 07:43:00

Thread: Doug's hollow form
13/03/2017 21:19:44

Thanks Derek. It's more a little box than a hollow form with the finial made from Blackwood.

This is a montage type picture I posted on Instagram which better shows the box & lid

Lidded pot

Thread: Which Ł200 extractor?
12/03/2017 21:27:29

Both extractors you mention Julian are more suited to shavings collection, if you are going to use one on your table saw you definitely want the fine filter as with the fabric bag filter all you will do is spread the fine dust further round your workshop as they only filter down to about 5 microns.

I've had an Axminster extractor with fine filter for around 12 years & have been very happy with it

Thread: Finishing Table Saw advice
05/09/2016 07:42:23

You only put a thin coat which is buffed up so any transfer would be negligible, also as the saw isn't giving a finished surface any contamination if you applied too much would be removed from the timber further along its preparation.

04/09/2016 10:17:15

If you want wood to slide easily over the table it is worth giving the top a coat of wax polish something like Chestnut's wood wax 22, I use this on surfaces I want to keep friction low, it's easy to apply, can be reapplied as & when necessary, I find it works very well.

Edited By Doug on 04/09/2016 10:19:39

Thread: Turnings
13/01/2014 19:23:18

Lovely Derek, a really nice piece.

cheers,

Doug

Thread: Hall Console Table
02/01/2014 18:00:33

That looks lovely Brian.

I really like the design & finish, thanks for sharing.

Cheers.

Doug.

Thread: oak bowl
01/01/2014 11:49:32

Lovely bowl Dennis with some very striking grain.

Cheers

Doug.

Thread: cutting an accurate curve in MFC
01/01/2014 11:46:45

Circle cutting jig

Hi Peter,

You could make a simple jig out of ply that fixes to the base of your router & allows you to cut arcs & circles.

The longer the jig the bigger the arc, this is mine for cutting circles, nothing complicated just made from a piece of Perspex.

Cheers

Doug

Thread: Happy New Year
01/01/2014 11:14:35

Hope you all had a great Christmas & best wishes for the new year.

Cheers.

Doug

Thread: East Midlands Woodworking Show
21/12/2013 12:44:51

I've been looking forward to this since first hearing about in the autumn as for a change it is only a few miles away from me.

Cheers,

Doug.

Thread: We wish you all a Merry Christmas
21/12/2013 12:42:00

Seasons greetings to one & all with best wishes for a happy & prosperous new year.

Cheers,

Doug.

Thread: Derek Lane's Woodewoker article
13/12/2013 08:28:29

Congratulations Derek,

Cheers.

Doug

Thread: Bandsaw Guides, Discs V Rollers
07/12/2013 17:37:19

I used to have a Record bandsaw with the disc type guides, they were fine on the sides of the blade but a groove was worn in the rear thrust guide from fairly early days of owning the saw.

When I upgraded I went for a machine with roller bearings & have been much happier with them.

Doug.

Thread: a faver for a faver
07/12/2013 17:31:41

Lovely bowl & some smashing looking timber Dennis.

You`ve done well to keep all the bark on, was the blank still a little green?

Doug.

Thread: Ron Fox
05/12/2013 07:43:20

Thanks to both of you.

Thread: cherry jewelry box
05/12/2013 07:38:59

Lovely work Wolfie, I`m sure your niece will be thrilled.

Thread: Ron Fox
30/11/2013 22:00:06
Posted by Steven on 30/11/2013 15:11:18:

Hi Doug,

I have made enquiries and waiting for a response, I will update to confirm.

The announcement I saw was from Peter Sefton who received the news from Ron’s daughter; this is indeed very sad news.

Thanks,

Steven

Thanks Steven,

I first saw about his death in a forum post elsewhere, I have since seen Peter`s announcement so can only presume that it is sadly true.

Doug.

Thread: Dovetail Stool
29/11/2013 22:54:17

Lovely stool David, some great woodwork there.

Cheers.

Doug.

Magazine Locator

Want the latest issue of The Woodworker incorporating Good Woodworking? Use our magazine locator links to find your nearest stockist!

Find The Woodworker inc Good Woodworking 

Latest Forum Posts
Support Our Partners
Peter Sefton IMPROVE FAST LONG
Felder UK April 2016
Wood Workers Workshop
Triton
Transwave 2017
Tormek
D B Keighley
Turners Tool Box
D&M Tools
Chippendale
Tool Post
Subscription Offers

Subscribe to<br />    The Woodworker Magazine and receive a FREE gift

Contact Us

We're always happy to hear from you, so feel free to get in touch!

Click here to find who to contact